Homepage[Homepage] - [Newsletter]
Search
or
orAdvanced search  Contact
Volume 1
 Warehouse and Administration
 Relief and Logistics Kits, ERU, RDU
 Personnel security equipment
 Radio and Telecommunication
 Power supply and electrical equipment
 Tools and Hardware
 Food
 Household
 Shelter and construction materials
 Livelihood
 Vehicles and consumables
 Water and Sanitation

Volume 2
 Drug products
 Medical disposable supplies
 Medical equipment
 Cold chain
 Laboratory
 Physical Rehabilitation

Volume 3
 Basic health care ERU
 Emergency care and triage
 Rapid Deployment Emergency Hospital
 Referral hospital ERU
 Surgical hospital, weapon wounded
 Medical kits
 Feeding and nutrition Kits
 Medical sets
 Surgical instruments and sets

 Introduction-Acknowledgements
 Quality-Standards-Inspection
 Item database, codes and description
 Units conversion
 Medical weight and volume
 Symbols
   Shelter tool kit
(Shelter and construction materials > Shelter, Construction, Kits)
< Back content list
last updated : 2015/10/29
Print
Product page
Specifications
Shelter tool kit
CodeDescriptionInd. priceShip. weightShip. vol.
KRELSHEK01
SHELTER TOOL KIT, tools and fixingsCHF 30,0011kg0.036

General information

The shelter tool kit is specifically designed for distribution after a disaster in which the shelter capacities of the population have been affected.

It is designed for family distribution, one kit per family.

This kit includes tools and hardware, only.

The shelter tool kit is also included in the shelter kit, refer to item code KRELSHEK02.

Purchase guideline for steel items: It may happen after long storage, that some items are presenting some rust stains. This must remain in an acceptable limit, and this is not a subject of rejection for the stained items.

Specifications

 

ROPE, polypropylene, black, 12mm diam., twisted

Diameter:

12mm +/- 0.5mm

Length:

30m

Weight:

1.9kg

Number of strand:

3 minimum

Type:

twisted

Material:

polypropylene, no recycled fibres, UV stabilized

Colour:

black

Tensile strength:

300kg

 

ROPE, polypropylene, black, 3mm diam., twisted

Diameter:

3mm +/- 0.2mm

Length:

30m

Weight:

0.1kg

Number of strand:

3 minimum

Type:

twisted

Material:

polypropylene, no recycled fibres, UV stabilized

Colour:

ll black

Tensile strength:

100kg

 

 

HANDSAW, for timber

Type & dimensions:

carpenter handsaw, 400-450mm blade, lacquered, overall length 550mm +/-50mm

Blade thickness:

1mm +/- 0.05mm, protected against oxidation

Blade protection:

Protective cardboard, teeth protection with hard, plastic cover.

Seal type:

laminated carbon steel, hardened and tempered

Number of teeth:

7-teeth per inch

Quality of make:

Soft edges but no dents, cracks or broken teeth

Hardness Rockwell C:

45 to 50 HRC for the whole blade, 48 to 52 HRC at teeth level

Carbon content:

0.47% to 0.55%

Manganese content:

0.5% to 0.8%

Handle:

Wooden dismountable handle, minimum 3 fixations, polished varnish hardwood, large 85x35mm opening  for hand comfort when wearing gloves. Optional 45/90° square. Moisture minimum 10%, maximum 15%.

Strength testing:

With the blade inserted into a 10mm-wide slot to a depth equal to 1/3 the blade's length, but not exceeding 150 mm, a deflection of 90° is applied 25 times in each direction without breakage or permanent set to the blade.

 

NAIL, FOR ROOF SHEETS, galvanized with watertight rubber washer, umbrella type

Type:

Iron nails, made of polished low-carbon steel, cold processed, not heat treated except for galvanization.

Shape:

Spiral rolled or twisted shank, sealed umbrella-type spring-head.

Corrosion treatment:

hot-dip galvanized at 300g/m2 +/-10%

Tensile strength:

minimum 650N/mm2

Accessories:

attached rubber washer with each nail

Dimensions (+/-5%):

shank: 75x3.6mm, head diameter: 20mm minimum

Rubber washer:

diameter 26mm x thickness 2mm

Packing:

packed in a strong, thick PE 130g/m² plastic bag, which can be zipped or locked

Quantity:

net weight: 0.5kg

 

SHOVEL, round point with Y handle

Material:

Pressed carbon-steel, hardened and tempered

Corrosion protection:

black paint

Quality of make:

no excess metal in the eye, no dents, no cracks, soft edges

Hardness Rockwell C:

35 minimum to 48 maximum HRC

Carbon content:

0.4% to 0.6%

Manganese content:

0.5% to 1%

Silicone:

0.37% maximum

Phosphorus & Sulphur:

0.06% maximum

Dimensions, full piece:

295 x 225mm +/-15mm

Hole diameter:

front side 36mm, back side 40mm, +/-5%

Weight:

1kg +/- 50g, without handle

Strength testing:

- Using a fitted, standard hardwood handle, clamp the blade of the shovel near the handle in a horizontal position. Gradually apply a load of 45kg and maintain it for 2 minutes. This should not result in any damage to the blade or a loosening of the handle, and no permanent set in excess of 25mm.

- With one centimetre of the end of the blade secured in a clamp, move the handle back and forth 30 degrees. There should be no permanent set greater than 25mm.

With the shovel held in a digging position, a 37mm in diameter piece of wood is hit hard against it. The blade should not buckle or break.

Handle:

No chips, rough surfaces, cracks, holes or knots. Smooth, polished varnish surface. Dry, strong and flexible wood. Moisture minimum 10%, maximum 15%. Handle adapted to head so that it can be blocked and secured with a nail.

Total length 1070mm +/- 50mm (head included).

The other end of the handle is made in a Y-shape with same quality of wood. The branches of the Y handle must be made of good-quality iron, securely fitted to the handle.

 

 

HOE, with long handle, large type

Material:

hot forged carbon steel, hardened and tempered, at a maximum the hardened zone should reach halfway up the back of the blade

Corrosion protection:

black paint

Quality of make:

no excess metal in the eye, no dent on the cutting edge, reinforced head with a rib from the eye to the middle of the blade length

Hardness Rockwell C:

35 minimum to 48 maximum HRC in hardened zone of the blade

Carbon content:

0.5% to 0.8%

Manganese content:

0.6% to 1.2%

Silicone:

0.37% maximum

Phosphorus & Sulphur:

0.06% maximum

Dimensions, full piece:

180 x 310 mm +/-10mm including the eye

Hole diameter:

high raised neck, front side 43 mm, back side 48 mm+/-2mm

Weight:

1.250kg +/- 150g, without handle, depending on the type of hoe

Strength testing:

- Using a fitted, standard hardwood handle, clamp the blade of the hoe near the handle in a horizontal position. Gradually apply a load of 45kg and maintain it for 2 minutes. This should not result in any damage to the blade or a loosening of the handle, and no permanent set in excess of 25mm.

- With one centimetre of the end of the blade secured in a clamp, move the handle back and forth 30 degrees. There should be no permanent set greater than 25mm.

With the hoe held in a digging position, a 37mm in diameter piece of wood is hit hard against it. The blade should not buckle or break

Handle:

No chips, rough surfaces, cracks, holes or knots. Smooth, polished varnish surface. Dry, strong, and flexible wood. Moisture minimum 10%, maximum 15%. Handle adapted to head so that it protrudes from and blocks on the other side of the head. Total length 1100mm to 1150mm.

 

 

MUTT HOE

Material:

hot forged carbon steel, hardened and tempered, at a maximum the hardened zone should reach halfway up the middle of the blade

Corrosion protection:

black paint

Quality of make:

no excess metal in the eye, no dent on the cutting edge, reinforced head with a rib from the eye to the middle of the blade length

Hardness Rockwell C:

35 minimum to 48 maximum HRC in hardened zone of the blade

Carbon content:

0.5% to 0.8%

Manganese content:

0.6% to 1.2%

Silicone:

0.37% maximum

Phosphorus & Sulphur:

0.06% maximum

Dimensions, full piece:

70 x 250mm +/-10mm

Hole diameter:

straight neck, low end 43mm, top end 48mm +/-2mm

Weight:

0.700kg +/- 50g, without handle

Strength testing:

- Using a fitted, standard hardwood handle, clamp the blade of the hoe near the handle in a horizontal position. Gradually apply a load of 45kg and maintain it for 2 minutes. This should not result in any damage to the blade or a loosening of the handle, and no permanent set in excess of 25mm.

- With one centimetre of the end of the blade secured in a clamp, move the handle back and forth 30 degrees. There should be no permanent set greater than 25mm.

 

 

 

 

MACHETTE

Type:

curved blade, 405mm/16″, lacquered against oxidation, overall length 55cm

Blade thickness:

2.5mm thick with 3 grooves that runs the full length of the blade to key in the handle

Handle:

wooden handle with 3 aluminium rivets plus washers

Material:

hot forged carbon steel, hardened and tempered, hardened throughout the entire blade, but remains normal past the first rivet hole.

Protection:

blade packed in carton pocket for protection.

Quality of make:

no dent on the cutting edge

Hardness Rockwell C:

45 minimum to 50 maximum HRC near cutting edge, test 3 positions along the cutting edge

Carbon content:

0.48% to 0.65%

Manganese content:

0.6% to 1%

Silicone:

0.37% maximum

Phosphorus & Sulphur:

0.03% maximum

Handle:

No chips, rough surfaces, cracks, holes or knots. Smooth, polished varnish surface. Dry, strong, hardwood. Moisture minimum 10%, maximum 15%.

Strength testing:

Insert the blade in a 10mm-wide slot up to a depth equal to 1/3 its blade length, but not exceeding 150mm; apply a deflection of 45° in each direction without breakage or permanent set to the blade.

 

 

SHEARS, straight, for metal sheet, semi-hard 0.8mm max., 260mm

Type:

tin snips for intensive use and easy maintenance

Make:

each blade and handle forged as one piece, symmetrical blades

Capacity:

up to 0.8mm semi-hard iron sheet

Material:

hot forged carbon steel, hardened and tempered, special treatment applied to the blade edge

Rustproof:

protected against corrosion with special paint

Dimensions:

overall length: 250 to 260mm

Maintenance:

dismountable in 2 parts only, with bolt and self locking nut

 

NAIL, iron, for wood, large

Type:

iron nails, made of polished low-carbon steel, cold processed, not heat treated except for galvanization

Rustproof:

hot dip galvanized at 300g/m2 +/-10%

Tensile strength:

minimum 650N/mm2

Shape:

flat, smooth, circular head; plain, round shank and diamond point

Dimensions (+/-5%):

ll length x diameter: 75x3.6mm, head diameter: 7.7mm

Packing:

packed in strong, thick PE 130g/m² plastic bag, which can be zipped or locked

Quantity:

net weight: 0.5kg per type

 

 

NAIL, iron, for wood, small

Type:

iron nails, made of polished low carbon steel, cold processed, not heat treated except for galvanisation.

Rustproof:

hot dip galvanised at 300g/m2 +/-10%

Tensile strength:

minimum 650N/mm2

Shape:

ll flat smooth circular head, plain round shank and diamond point.

Dimensions (+/-5%):

ll length x diameter: 40x2.2mm, head diameter: 5mm to 5.5mm

Packing:

packed in strong thick PE 130g/m² plastic bag, which can be zipped or locked

Quantity:

net weight: 0.5kg per type

 

TIE WIRE, galvanised, diam. 1.5 mm, 25m, roll

Material

ll low carbon steel, hot dip galvanised with minimum 40g/m2, binding /tie wire.

Quantity

roll of 25m.

Dimension

diameter 1.5mm +/-5%

Tensile strength

minimum 340 N/mm² to Maximum 500N/mm

 

 

CLAW HAMMER

Type:

Carpenter hammer, head and handle, hammer head with flat and claw side, as per ISO15601, except for the pull-apart test force.

Material:

high-carbon steel head, treated to achieve a martensitic structure, with dressed striking faces

Quality of make:

smooth surface and edges with no dents or cracks; no excess metal in the eye

Weight of the hammer:

Total weight 750g +/- 50g (equivalent to 700g minimum, 800g maximum)

Hardness Rockwell C:

50 minimum to 58 maximum HRC on striking faces

Hardness Rockwell C:

35 maximum HRC closed to the eye

Handle: No chips, rough surfaces, cracks, holes or knots. Smooth, polished varnish surface. Dry, strong, and flexible wood. Handle adapted to head so that it protrudes and can be blocked on other side with a metal wedge on the other side of the head. Moisture minimum 10%, maximum 15%.

Pull-apart test: ISO15601. After two series of 25 vigorous blows with varying delivery angle, secure head in a clamp, apply a minimum traction of 50kg trying to pull the handle out. This should not damage the hammer head or the handle, and the handle should remain firmly attached to the head.

Bending test: ISO15601. For the claw hammer only, apply a load perpendicularly to the axis of the handle and close to the end, so as to obtain a 125Nm torque, irrespective of the size of the hammer. Start the load at zero and increase gradually, without jerking. Hold the test load for at least 10s. This should not create any damage to the hammer head or handle.

 

MEASURING TAPE, tailor type

Type:

Flexible measuring tape, tailor type, 3m long

Material:

PVC coated polyester

Quality of make:

Minimum thickness … mm

Weight

Minimum weight …g

 

 

CURVED NEEDLE, hand stitching

Type:

Curved needle, for hand stitching, 127mm x 1.8mm, hole 1mm x 7mm

Material:

Stainless steel

Quality of make:

Bending strength …?

Weight

Minimum weight …g

 

 

POLYETHYLENE BAG (1 bag per kit)

Material:

Standard ICRC/IFRC tarpaulin, white, without the bands

Type:

Square rectangular base duffle bag with 6 aluminium or galvanised steel eyelets and a 10mm PP rope for closing that can also act as a shoulder handle.

Dimensions:

Total length 1250mm

Final packed maximum dimension 1200x300x150mm +/-10mm

The closing rope of the bag can be detached from the bottom of the bag and packed inside the mouth of the bag. The bag is securely sealed with a plastic strap with manual opening.

Includes a copy of the content list for the complete shelter kit printed on the outside of the bag; and a copy of the user's instruction, printed on durable textile or laminated paper, placed inside the bag. Original user's instruction document available in here below attachment “specifications.pdf”

Customer's marking and logo printed on the outer bag in durable printing

Tarpaulins are not packed in this bag.

 

 

CARDBOARD FOLD (1 per kit)

Material:

Double-walled corrugated cardboard.

Type:

One or several pieces of cardboard in which the complete kit is securely packed before being placed in the bag. The cardboard folds on the 2 long sides and one short side.

Dimensions:

To fit in the outer bag

Sealing:

Strapped with 2 heat-sealed 10mm minimum plastic straps.

Quality:

Loaded cartons should withstand 1m-high stacking on pallets, and several handlings (hand and forklift) without damage

Palletising:

The pallets (wood or metal) are made or reinforced in such a way that allows 2 levels stacking (stacking up to 2m high), without any damage for the kits and the kit packaging.

 

Remark: Tarpaulins are packed separately.

 

IFRC/ICRC Emergency Items Catalogue - Shelter tool kit specification October 29th, 2015      page 2/7

 

Specifications.pdf
Content list - Export content list (excel file)
CodeDescriptionQty
APACBAGSPE180BAG, duffle type, coated polyethylene 180g/m², 1300x400mm1
EHDWNAILRS01NAILS, ROOFING, 75mm (3"), hot galva. + rubber washer, 0.5kg1
EHDWNAILW040NAILS, hot galvanised iron, for wood, 40mm, (1.1/2")1
EHDWNAILW075NAILS, hot galvanised iron, for wood, 7.5cm (3")1
EHDWWIRETR15TIE WIRE, galvanised, diam. 1.5 mm, 25m, roll1
EMEATAPMTA30MEASURING TAPE, tailor type, PVC coated polyester, 20mm x 3m1
ETOOCUTTSHE1SHEARS, straight, for metal sheet, semi-hard 1mm max., 255mm1
ETOOHAMMCARWCLAW HAMMER, carpenter type, 750g, wood handle1
ETOONEELC12NEEDLE, stitching, curved, 127mm x 1.8mm, hole 1x7mm2
ETOOSAWSW400HANDSAW, for timber, 400mm blade1
HSHEROPE03PROPE, POLYPROPYLENE, diam. 3mm, twisted, green30
HSHEROPE12PBROPE, POLYPROPYLENE, black, diam. 12mm, twisted30
RAGRTOOLHOE3HOE, with long handle, large type1
RAGRTOOLHOE4HOE, MUTT HOE, head only, 250x70mm, 0.7kg1
RAGRTOOLMAC1MACHETTE, approx. length 500mm, wooden handle1
RAGRTOOLSHO2SHOVEL, round point with Y handle, total lenght approx.1m1
Options / Accessories
  PLASTIC SHEETING, woven, 4x60m, white/white, roll
About this site and copyright
powered by SolidPepper